Your Plumbing Crash Course: A Guide to Installing a Bathtub
Your Plumbing Crash Course: A Guide to Installing a Bathtub
Blog Article
On this page below you might get lots of sound facts involving Tools You Need to Install a New Bathtub .
Setting up a tub isn't specifically rocket science, yet it does call for solid plumbing, woodworking, and often, tiling abilities. Replacing an old bath tub with a brand-new one is also a reasonably challenging job. If the old tub is conveniently easily accessible, the task can move speedily; if you need to open up a wall surface to remove the old bathtub as well as position the brand-new bath tub, the job is much harder. In either situation, the task is within a home handyman's abilities, although you will require a helper to move out the old tub as well as set in the new one. See to it you have qualified yourself for the task as well as are comfortable trying it. As opposed to working with a service provider to take over a halfway-completed task, it is much better to take into consideration using one before you begin. Possibilities are you might need an expert plumber to make tube connections.
This post will aid you mount a brand-new bath tub in your washroom if you have actually currently acquired a brand-new tub and also do not need to change the setup of your previous water supply pipelines.
Your tools as well as product checklist ought to make up the following:
Preparing for the Installation
First of all, the sustaining structure supplied with the bath must be fitted (if called for) according to the supplier's instructions. Next off, fit the taps or mixer to the bath tub. When fitting the faucet block, it is important to see to it that if the tap features a plastic washing machine, it is fitted between the bathroom and the faucets. On a plastic bathroom, it is likewise practical to fit a supporting plate under the faucets system to stop pressure on the bath tub.
Fit the versatile faucet ports to the bottom of the two faucets using 2 nuts and also olives (sometimes supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the outlet via the hole in the bathroom. Make use of the nut supplied by the maker to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the versatile overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bath. See to it you use all of the provided washing machines.
Attach the catch to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Link all-time low of the overflow tube in a comparable manner.The bathroom ought to now prepare to be suited its final setting.
Removing Old Touches
If you need to replace old taps with brand-new ones as a part of your installment, then the first thing you ought to do is detach the water system. After doing so, switch on the taps to drain any kind of water staying in the system. The procedure of getting rid of the existing taps can be rather bothersome because of the restricted gain access to that is usually the instance.
Use a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that attaches the supply pipes to the faucets. Have a fabric ready for the staying water that will certainly originate from the pipelines. As soon as the supply pipes have actually been eliminated, make use of the same tool to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to quit the single faucets from turning during this procedure. Once the taps have been gotten rid of, the holes in the bath/basin will certainly have to be cleansed of any type of old securing substance.
Before going on to fit the new faucets, compare the pipe connections on the old faucets to the brand-new taps. If the old faucets are longer than the new faucets, after that a shank adapter is needed for the brand-new faucets to fit.
Installing the Bath tub
Making use of both wood boards under its feet, put the bathtub in the needed setting. The wood boards are valuable in evenly spreading out the weight of the bath tub over the area of the boards as opposed to focusing all the weight onto 4 little factors.
The next goal is to make certain that the bathtub is leveled all round. This can be achieved by inspecting the spirit level as well as readjusting the feet on the bathtub until the spirit level reviews degree.
To install taps, fit all-time low of the outermost adaptable faucet adapter to the ideal supply pipeline by making a compression join; then do the exact same for the other tap.
Turn on the water supply and also inspect all joints and new pipework for leaks and also tighten them if required. Load the bath tub as well as likewise examine the overflow outlet as well as the regular outlet for leakages.
Lastly, fix the bathroom paneling as described in the producer's user's manual. Tiling as well as sealing around the bath tub should wait till the bathtub has been utilized a minimum of when as this will certainly settle it right into its last placement.
Suitable New Touches
If the tails of the brand-new faucets are plastic, after that you will need a plastic port to prevent damage to the string. One end of the connector fits on the plastic tail of the faucet and also the other end offers a connection to the current supply pipes.
If you require to fit a monobloc, then you will need lowering couplers, which links the 10mm pipe of the monobloc to the standard 15mm supply pipe.
Next, place the faucet in the mounting hole in the bath/basin guaranteeing that the washing machines are in area in between the tap and the sink. Protect the tap in place with the producer offered backnut. As soon as the tap is safely in place, the supply pipes can be attached to the tails of the taps. The faucets can either be attached by utilizing corrugated copper piping or with normal tap connectors. The former type ought to be attached to the tap finishes first, tightening just by hand. The supply pipes can later be attached to the other end. Tighten up both ends with a spanner after both ends have actually been connected.
Tiling Around the Tub
In the location where the bath satisfies the ceramic tile, it is necessary to secure the accompanies a silicone rubber caulking. This is necessary as the fitting can relocate enough to crack a rigid seal, creating the water to pass through the wall surface in between the bath and the tiling, causing issues with dampness and feasible leaks to the ceiling listed below.
You can select from a range of coloured sealants to assimilate your fixtures as well as installations. They are offered in tubes as well as cartridges, and can securing gaps approximately a size of 3mm (1/8 inch). If you have a larger space to load, you can load it with spins of drenched newspaper or soft rope. Keep in mind to constantly fill the bath tub with water before securing, to allow for the movement experienced when the bathtub is in use. The sealer can fracture relatively very early if you do not take into account this activity before securing.
Additionally, ceramic coving or quadrant ceramic tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are likewise easily available on the market. It is advisable to fit the ceramic tiles making use of water-resistant or water resistant adhesive as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As a keen reader about Installing A Bathtub, I imagined sharing that chunk was a great idea. If you please take the opportunity to share this post if you enjoyed reading it. I take joy in reading our article about Tools You Need to Install a New Bathtub .
Call now! Report this page